TrueVIS SG-540 Printer/Cutter Specifications
Specifications
| Model | SG-540 | ||
|---|---|---|---|
| Printing technology | Piezoelectric inkjet | ||
| Media | Width | 8.3 to 54 in (210 to 1371 mm) | |
| Thickness | Maximum 39 mil (1.0 mm) with liner for printing | ||
| Maximum 16 mil (0.4 mm) with liner and 9 mil (0.22mm) without liner for cutting | |||
| Roll outer diameter | Maximum 8.3 in. (210 mm) | ||
| Roll weight | Maximum 66 lbs (30 kg) | ||
| Core diameter *1 | 3 in. (76.2 mm) or 2 in. (50.8 mm) | ||
| Printing/cutting width *2 | Maximum 53 in (1,346 mm) | Maximum 29 in 736 mm) | |
| Ink | Type | Roland TrueVIS INK | |
| Capacity | 500 cc | ||
| Colors | CMYK | ||
| Printing resolution (dots per inch) | Maximum 900 x 900 dpi | ||
| Maximum Speed (CMYK, 7 pass) | 101.2 ft2/hr | ||
| Standard Speed (CMYK, 10 pass) | 85 ft2/hr | ||
| Cutting speed | 10 to 300 mm/s (0.4 to 11.8 in/s) | ||
| Blade force *3 | 30 to 500 gf | ||
| Blade offset | 0 to 0.059 in (0 to 1.5 mm) | ||
| Software resolution (when cutting) | 0.000984 in/step (0.025 mm/step) | ||
| Distance accuracy (when printing) *4 *5 | Error of less than ±0.3% of distance traveled, or ±0.3 mm, whichever is greater | ||
| Distance accuracy (when cutting) *3 | Error of less than ±0.4% of distance traveled, or ±0.3 mm, whichever is greater | ||
| When distance correction has been performed (when the setting for [CUTTING MENU] – [CALIBRATION] has been made): Error of less than ±0.2% of distance traveled, or ±0.1 mm, whichever is greater | |||
| Repeatability (when cutting) *4 *6 | ±0.1 mm or less | ||
| Alignment accuracy for printing and cutting *4 *7 | ±0.5 mm or less | ||
| Alignment accuracy for printing and cutting when reloading media *3 *7 | Error of less than ±0.5% of distance traveled, or ±3 mm, whichever is greater | ||
| Media heating system *8 | Print heater | Setting range for the preset temperature: 86 to 112ºF (30 to 45ºC) | |
| Dryer | Setting range for the preset temperature: 86 to 122ºF (30 to 50ºC) | ||
| Connectivity | Ethernet (10BASE-T/100BASE-TX, automatic switching) | ||
| Power-saving function | Automatic sleep feature | ||
| Power requirements | AC 100 to 120 V ±10%, 9.8A, 50/60 Hz | ||
| AC220V to 240V±10%, 4.0A, 50/60Hz | |||
| Power consumption | During operation | 1,050 W | |
| Sleep mode | 20 W | ||
| Acoustic noise level | During operation | 65 dB (A) or less | |
| During standby | 48 dB (A) or less | ||
| Environmental | Power on (*10) | Temperature: 20 to 32°C (68 to 90°F), humidity: 35 to 80 % RH (no condensation) | |
| Power off | Temperature: 5 to 40°C (41 to 104°F), humidity: 20 to 80 % RH (no condensation) | ||
| Dimensions (with stand)) | 105.7(W) x 29.3(D) x 51.6(H) 2685(W) x 745(D) x 1310(H) mm | ||
| Weight (with stand) | 392 lb (178kg) | ||
| Included items | Stand, power cord, blade, blade holder, media clamps, media holder, replacement blade for separating knife, software RIP, user’s manual, etc. | ||
*1 The media holder of this machine is exclusively for media with a paper tube core inner diameter of 3 inches. To use a 2 inch media core, please use the optionally available media flanges.
*2 The length of printing or cutting is subject to the limitations of the program.
*3 500 gf is the maximum instantaneous blade force. The blade force must be adjusted according to details such as the media thickness.
*4 Using Roland specified media, print travel of 1m. Temperature: 25°C (77°F), humidity: 50%. Roll media must be loaded correctly. Applicable when all pinch rollers that can be used with the media width are used. Side margins: 25 mm (1.0 in.) or more for both the left and right margins. Front margin: 35 mm (1.4 in.) or more. Excluding expansion/contraction of the media. Not guaranteed when the print heater or dryer is used. Assumes all correction and adjustment functions of the machine have been used properly.
*5 Print travel: 1 m (39.4 in.)
*6 [PREFEED] menu item must be set to “ENABLE.” Range for assured repetition accuracy. 54″ model -For media with a width exceeding 24 in (610 mm in.): Length 315 in (8000 mm)- 30″ Model Width 24 in (610mm) or less: Length 118.2 in (4000 mm)
*7 Provided that the media feed length is 3,000 mm (118.1 in.) or less. Excludes the effects of slanted movement and of expansion and contraction of the media.
*8 Data size: 54″ Model: 39.4 in. (1000 mm) in the media-feed direction, 1,346 mm (53.0 in.) in the carriage-movement direction. 30″ Model: 39.4 in. (1000mm) in the media-feed direction, 29in.(736 mm)in the carriage-movement direction. No Lamination. Automatic detection of crop marks at 4 points when media is reloaded. During cutting, [PREFEED] menu item must be set to “ENABLE.” Excluding possible shift caused by expansion/contraction of the media and/or by reloading the media.
*9 Warm-up is required after the power is turned on. This may require 5 to 20 minutes, depending on the operating environment. Depending on the ambient temperature and the media width, the set temperature may not be reached.
*10 Operating environment: Use the machine in an operating environment within its range
| Roland VersaWorks 6 System Requirements | ||
|---|---|---|
| Operating system | Windows® 10 (32/64-bit) | |
| Windows® 8.1 (32/64-bit) | ||
| Windows® 7 Professional / Ultimate (32/64-bit) | ||
| CPU | Intel® Core™2 Duo, 2.0 GHz or faster recommended | |
| RAM | 2 GB or more recommended | |
| Video card and monitor | A resolution of 1,280 x 1,024 or more recommended | |
| Free hard-disk space | 40 GB or more recommended | |
| Hard-disk file system | NTFS format | |
| Optical drive | DVD-ROM drive | |
| Other requirements | Ethernet or USB port Internet connection and web browser to use Roland@NET |
|
Please note: Considering that you will be using software such as Illustrator, we recommend that you use as high performance computer as possible to reduce RIP processing time. We also recommend using a hard disk that has large enough capacity, as print files are often tens of GB in size (or larger) when data is high resolution.
* Roland VersaWorks 6 is a 32-bit application, which runs on 64-bit Windows® with WoW64 (Windows 32-bit on Windows 64-bit).
| Roland VersaWorks 6 System Requirements | ||
|---|---|---|
| Operating system | Windows® 10 (32/64-bit) | |
| Windows® 8.1 (32/64-bit) | ||
| Windows® 7 Professional / Ultimate (32/64-bit) | ||
| CPU | Intel® Core™2 Duo, 2.0 GHz or faster recommended | |
| RAM | 2 GB or more recommended | |
| Video card and monitor | A resolution of 1,280 x 1,024 or more recommended | |
| Free hard-disk space | 40 GB or more recommended | |
| Hard-disk file system | NTFS format | |
| Optical drive | DVD-ROM drive | |
| Other requirements | Ethernet or USB port Internet connection and web browser to use Roland@NET |
|
Please note: Considering that you will be using software such as Illustrator, we recommend that you use as high performance computer as possible to reduce RIP processing time. We also recommend using a hard disk that has large enough capacity, as print files are often tens of GB in size (or larger) when data is high resolution.
* Roland VersaWorks 6 is a 32-bit application, which runs on 64-bit Windows® with WoW64 (Windows 32-bit on Windows 64-bit).